Functionally they are the same but the newer Mac version has slightly different menus. While there is a newer version for Mac users, this older version still seems to be what they are using on Windows. The newer version has a slightly different menu structure but functionally it is just the same. If you have an older version like the one described here, it should work just fine. There us a newer version of the Airport Utility but this version works fine. The airport utility is found in your applications folder. The instructions here are done on a Windows computer, but the Mac version of the Airport Utility is virtually identical. Note that the Wan and Ethernet ports are exactly the same, but if you plug in the wrong port, your device will not connect. I am putting the cable in the middle plug. There are four ethernet ports in my airport. It's possible to configure via wireless, but it works better to use a cable. Run a cable from your Mac to the Airport and plug it into one of the ethernet ports that is labelled like this: ![]() The wan port has a little "o" shaped symbol next to it that looks like this: ![]() Connecting to the AirportĬonnect an ethernet cable from your modem to the "Wan" port (see diagram above). If you are using the older version of the Mac Utility it will look about the same. This instruction sheet will show you how to configure using a Windows computer using the Airport Express Utility 5.6 for Windows. It can be configured with either Mac or Windows. The Airport Express is a router made by Apple. I don’t have enough knowledge to tell how/if it is possible to point Wireshark to such a PCMCIA card, or to get it to watch a growing dump file, to allow live analysis but I think it’s a plausible project.Setting up DSL with Apple Airport Utility 5.6 for Windows/Mac Since Wireshark allows review of dumps you could then run them through the Wireshark analyzer. If you use a Prism II chipset PCMCIA card in a Powerbook, or use another wireless card which is supported appropriately by the wireless sourceforge drivers, you may be able to use software such as KisMAC to dump to file full frames captured in passive mode. Then “airport -I” shows the current channel, among other things, “airport -z” disassociates from any network, and “network -c” sets the channel. As the command is not in the standard path, you might find it convenient to set up a link, as shown in : sudo ln -s /System/Library/PrivateFrameworks/amework/Versions/Current/Resources/airport /usr/sbin/airport You can use the undocumented “airport” command to disassociate from a network, if necessary, and set the channel. It’s possible to capture in monitor mode on an AirPort Extreme while it’s associated, but this necessarily limits the captures to the channel in use. With versions earlier than 1.4, see the description of how to enable monitor mode on 10.5.x. With Wireshark 1.4 or later, to capture in monitor mode on an AirPort Extreme device, check the “Monitor mode” checkbox in the “Capture Options” dialog (in Wirehark before 1.8) or in the “Edit Interface Settings” dialog for the interface in Wireshark 1.8 and later. In Mac OS X 10.6.x (Snow Leopard) and later versions, monitor mode is supported 802.11 headers are provided, and non-data frames are captured, only in monitor mode. To capture in monitor mode on an AirPort Extreme device, select a “Link-layer header type” other than “Ethernet” from the Capture -> Options dialog box in Wireshark or by selecting a link-layer header type other than “EN10MB” with the “-y” flag in TShark or from the command line in Wireshark (the available link-layer types are printed if you use the “-L” flag). ![]() In Mac OS X 10.5.x (Leopard), monitor mode is supported 802.11 headers are provided, and non-data frames are captured, only in monitor mode. On PowerPC Macs, you will have to enable that device by changing the !APMonitormode property in the /System/Library/Extensions/AppleAirport2.kext/Contents/ist property list file to have the value “true” () and rebooting on Intel Macs, that device is enabled by default. To capture in monitor mode on an AirPort Extreme device named en n, capture on a device named wlt n instead – for example, if your AirPort Extreme device is named en1, capture on wlt1. In Mac OS X 10.4.x (Tiger) (at least in later updates), monitor mode is supported 802.11 headers are provided, and non-data frames are captured, only in monitor mode. In Mac OS X releases prior to 10.4.0 (Panther and earlier), neither monitor mode, nor seeing 802.11 headers when capturing data, nor capturing non-data frames are supported – although promiscuous mode is supported. Using Apple’s own AirPort Extreme 802.11 wireless cards:
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |